Abstract

This study characterizes the dynamic responses of hammer weight and drop height in dynamic penetration tests. The tests were conducted using an instrumented dynamic cone penetrometer (IDCP) to obtain the dynamic responses during penetration. Various hammer weight and drop height types were used at a fixed potential energy of 45.1 N∙m. The measured compression stresses and transferred energies into the rod head and cone tip were analyzed for hammer weight and drop height. The compression stress at the rod head varied with the hammer weight and drop height, whereas the compression stress at the cone tip is irrelevant to the hammer weight or drop height. In addition, the transferred energies into the rod head and cone tip increased as the hammer weight increased but decreased as the drop height increased. This study demonstrates that hammer weight and drop height should be considered when the characteristic of subsurface is profiled using dynamic penetrometer.

Abstract

Dynamic penetration tests DPT have been routinely employed in the geotechnical characterization of the subsoil in different types of engineering projects. The evaluation of the results of these tests has been performed considering a limited number of parameters obtained in the field, so the definition of new parameters allows a more accurate evaluation of soil characteristics. The purpose of this paper is to present a methodology for the evaluation of the dynamic modulus (Ekd) based on the analysis of the dynamic force and velocity signals recorded in each hammer impact. Variable energy DPT tests were performed on Fontainebleau NE34 sand specimens in a K0 calibration chamber. For each hammer impact on the penetrometer, a decoupling and wave reconstruction method was applied to obtain the force and velocity signals at the cone-soil interface, which are analyzed in the frequency spectrum to obtain the Ekd modulus. The results show that it is possible to evaluate the dynamic modulus at different vertical loading conditions and independent of the impact energy level of the hammer on the penetrometer.

Abstract

During the so‐called vibro‐penetration test (VPT), a vertical harmonic excitation force drives a rod with a conical tip into the ground. For the evaluation of the VPT resistance, an energy‐corrected number of vibration cycles Nz10 for 0.10 m penetration is used. In order to determine Nz10, the dynamic penetration resistance, the tip and shaft resistance, the tip acceleration, and the depth of the penetrometer tip are continuously recorded and processed according to a mechanical vibro-penetration model. Calibration chamber tests, field tests, and Finite Element Analyses, which were carried out to validate the assumed penetration mechanism and to investigate the influence of the state variables (density and effective stresses) and the machine parameters (static moment, frequency, and static load) on the penetration resistance. As the force and displacement of the penetrometer are determined at the tip, an equivalent spring stiffness, which is correlated with the soil stiffness, can be calculated over the driving depth. Since vibro‐penetration resistance is closely related to the soil behavior under cyclic shearing, the VPT should be more appropriate than monotonic tests to characterize the ground response to repeated dynamic and alternating loading, e.g. pile drivability, ground compaction, and soil liquefaction susceptibility. Compared with the cone-penetration test (CPT), the VPT equipment is much lighter, the execution time is shorter, and in‐situ investigations of medium-dense to dense cohesionless soils at large depths are feasible. In this contribution, VPT and CPT are used to investigate the effect of blasting compaction in very loose dumps from opencast mines in Lusatia, Brandenburg, Germany. It is concluded that the VPT results are reproducible. In addition, Nz10 shows a clear correlation with the state variables and the VPT records before and after blasting compares well with the results of CPT.

Abstract

Based on the principle of the Panda® penetrometer, a third-generation of variable-energy dynamic cone penetrometer has been developed in France: the Panda 3(1). This is an instrumented dynamic penetrometer which, by measuring strain, acceleration, and displacement on the rods, close to the anvil, and then decoupling the deformation waves created by the impact and propagating within the rods during penetration, makes it possible to obtain for each blow, at the soil/cone interface, a dynamic load penetration curve, called DCLT curve. Several experimental and numerical studies have been carried out to develop different techniques for processing DCLT curves and dynamic signals to assess input energy, dynamic and pseudo static cone resistance, dynamic stiffness, elastic modulus, and compressional wave velocities of soil. This technique has been adapted to the DPSH cone penetrometer (ISO 22476-2), for which it was necessary to servoassisted the impact force as a function of the soil penetration obtained after each blow to improve then the quality of the signals and DCLT curves obtained. Recently, in France, a vast experimental program involving two universities and two geotechnical companies was carried out to develop this new technique. A large laboratory and in-situ test data base was performed. After a brief presentation of the theoretical and technological development of this new technique is presented.

Abstract

Dynamic penetrometer is a worldwide practice in geotechnical exploration and the French Panda (1) lightweight variable energy is the most developed device nowadays. Widely used in France and other countries, The Panda penetrometer is relatively unknown for characterizing surface soils domain and the possibilities it offers. In this article, the authors offer a brief review of the principle of measurement, its uses, advantages and disadvantages calibration, and interpretation, as well as the different relationships with other in-situ test (CPT, SPT…) and some geotechnical parameters. A summary of the works that can be found and that are based on this technology is also presented. The overall aim is to provide the reader with a basic historical document for a better understanding of the operation and analysis of the results obtained with this device, enabling it to be integrated, as a complement, into in situ investigation campaigns.

Abstract

Chile is the third country with most tailing dams worldwide (764, of which 15% active, 62% inactive, and 23% abandoned). Today, one of the main challenges of the mining industry is to ensure environmental sustainability. To achieve this, it is not only necessary to have regulations guaranteeing correct design, maintenance, closure stages, but also supervision and suitable technology enabling rapid, reliable, and cost-effective diagnosis of the overall tailings dam stability. For the last 20 years, French instrumented dynamic cone penetrometer, P.A.N.D.A®, has been used for in-depth quality control of tailings deposits, mainly due to its rapidity, portability, easy-to-use, cost-effective, and environmentally friendly testing which is based on standardized methods and able to produce immediate results. The last few years, different studies have been carried out to characterize tailings dams from a geotechnical perspective as well as to assess their spatial and temporal variability. This article presents a summary of the 20 years of Chilean experience in compaction quality control and geotechnical characterization of mine waste facilities using P.A.N.D.A® to assess the overall stability, slope analysis stability, liquefaction triggering, spatial variability of material properties and evaluation of some geotechnical parameters. Indeed, given the scale of the problem these structures represent for the community and the environment, it seemed necessary to bring together most of the work carried out in Chile to propose an innovative alternative to the rest of the mining community.

Abstract

This work presents both a summary of its implementation at two post-seismic sites: the island of Cephalonia (Greece), and the Petrinja (Croatia) along the Kupa river. In the first case, the main objective was to characterize the surface formations of the Koutavos plio-quaternary sedimentary basin to propose a 1D model of the surface soil column and assess the influence of the variability of these surface formations on the amplification of seismic motion. The second experimental campaign in Croatia was aimed at identifying the soil layers that had been liquefied following the events of 2020, as well as highlighting the different soil models obtained by geophysics or constructed from instrumented variableenergy DCP. For each investigated site, additional geophysical and geotechnical tests were carried out. The data collected with this new technology were compared with those obtained previously with other geophysical methods (MASW), in order to assess the shear wave velocity obtained in particular.