Abstract

Several approaches are investigated to model interior reinforced concrete waffle-flat-plate-column connections. A model is proposed that provides very good results with reasonable low computational cost. The proposed model is validated with the experimental results obtained on a 3/5 scale specimen, subjected to quasi-static in cyclic loads up to collapse. To this end, the non-linear advanced theory of reinforced concrete is applied on a three-dimensional finite element model and non-linear analysis are conducted. Both fiber and layer elements are used for the one-dimensional and bi-dimensional components respectively. The main results of the simulation were: (i) the capacity curve obtained through out a push-over analysis with displacement control, (ii) the hysteretic curves of the slab, and (iii) the crack patterns. A very good agreement is found between numerical and experimental results.

Abstract

Collapsible unsaturated soils are characterized by a low-density composition and exhibit sudden settlement after wetting while maintaining in-situ stress levels. This issue is effectively mitigated by compaction, a simple and economical technique that improves the soil properties and geotechnical behaviour. In this study, the collapsible behaviour of a compacted sandy laterite soil is analysed, focusing on the influence of relative compaction, water content, initial suction and inundation stress. The primary aim is to analyse the effect of initial compaction conditions on collapse potential. Conventional and suction-controlled oedometer tests were conducted on soils from Ilha Solteira, São Paulo, Brazil, where there is a large amount of geotechnical data available. The laboratory data reveal that collapse deformations of compacted soil depend on relative compaction, initial water content, soil suction, and inundation stress. Poorly compacted soils exhibit greater susceptibility to collapse when wetted, and the magnitude of collapse potential varies with water content. Additionally, this study shows the influence of initial suction on collapsibility of less compacted soils. The laboratory results highlighted the importance of considering suction and inundation stress in understanding the collapsible behaviour of compacted soil, whereas traditional empirical methods often emphasize low density and water content as primary factors predisposing soils to collapse.

Abstract

The in situ Engineered Barrier (EB) experiment aimed at understanding the hydromechanical behaviour of sealing materials for high-level radioactive wastes as a combination of compacted blocks and high-density pellets made of Febex bentonite. The experimental program focused on the wetting process of a heterogeneous dual-component sample consisting of pellets and blocks with technological gaps. The homogenisation tendency was investigated by determining the final (local) dry densities and pore size distributions in both zones from post-mortem analyses. Global initial dry densities between 1.36–1.44 Mg/m3 were considered for the heterogeneous mixture, wetted at constant volume and constant vertical stress (oedometer conditions). The initially high-density zone of blocks with technological gaps expanded during hydration, reaching a lower dry density at saturation than the pellets’ zone. The initially low-density pellets’ zone with a high volume of inter-pellet pores underwent compression and reached a final high dry density on saturation. The experimental results were compared with the distribution of dry density at the in situ EB experiment after dismantling, and a good agreement between the laboratory and the in situ measurements was observed.

Abstract

The Cone Penetration Test (CPTu) can be used to evaluate the soil behaviour and properties through correlations (empirical and/or analytical), and the results must be compared to laboratory tests to be validated. This paper presents the evaluation of the effective friction angle (φ’) of a stiff over-consolidated Brazilian clay based on CPTu data and laboratory tests characterization, such as index properties, and the comparison of the effective shear strength parameters obtained by triaxial tests. Based on CPTu data, the soil was classified using the Soil-Behaviour Type Classification System (SBTn) proposed by Robertson (2016), and properties such as over-consolidation ratio (OCR) and the effective friction angle were determined using well-known correlations such as Chen & Mayne (1996) and Ouyang & Mayne (2019). The shear response defined by CPTu was compared to the results of isotropic consolidated triaxial compression tests (CIUC). The results showed mainly a clay-like behaviour based on the CPTu data, in agreement with the laboratory characterization, which indicated high plasticity. Regarding the shear response, both the triaxial test and the CPTu data indicated dilative behaviour under shear. Furthermore, the effective friction angle obtained from the triaxial test and the CPTu data were similar depending on the OCR used in the equation, demonstrating the applicability of the adopted methodologies for the Brazilian stiff over-consolidated clay. Finally, based on CPTu data it is proposed a complement of the SBTn developed by Robertson (2016) with OCR isolines.

Abstract

Diatomaceous soils, composed of diatom fossils and clay minerals typically formed in volcanic environments, exhibit characteristics such as low unit weight, high plasticity and liquid limit, significant compressibility, and high friction angles. Despite their presence in various locations globally, knowledge about their geotechnical behavior is limited and primarily based on laboratory tests conducted on artificial samples. This paper presents data obtained from undisturbed samples of natural diatomaceous soils and discusses the interpretation of Cone Penetration Test with Pore Pressure (CPTU) data to classify these complex non-textbook soils and estimate their mechanical properties. The study area is situated in the Po Plain near the thermal anomaly region of the Euganean Hills in Northeast Italy. Three CPTUs and one borehole with the collection of four Osterberg undisturbed samples were conducted. Laboratory tests on the undisturbed samples provided values for Atterberg Limits, soil unit weight, in-situ void ratio, compressibility, and permeability, which were compared with estimations derived from CPTU data analysis. Moreover, Scanning Electron Microscope images provided insight into the distinctive microstructure of diatom microfossils embedded in a clayey matrix. Based on these comparisons, CPTU proves to be effective in estimating relevant parameters of diatomaceous soils, particularly the Soil Behavior Type (SBT) and consolidation coefficient from dissipation tests. However, the agreement in estimating the oedometric modulus is less satisfactory. Therefore, for a precise definition of the geotechnical model, it is recommended to conduct additional laboratory tests, particularly those focused on defining compressibility parameters, given the unique behavior of natural diatomaceous soils.

Abstract

Characterization of the geomechanical behavior of the seabed along a high-pressure high-temperature (HPHT) pipeline route is important for understanding risks from geohazards and thermally induced displacements such as axial walking. Axial resistance to pipeline displacement, from the friction between seabed and the contact surface of the pipe, can be estimated through laboratory tests using interface shear box (ISB) and tilt table. Tests performed by NGI in several developements in Gulf of Mexico, South America, and West Africa revealed significant variation in shear resistance, potentially associated with the type of interface material and surface roughness characteristics. This paper illustrates the effect of clay activity and interface surface material on the residual undrained interface strength estimated from interface shear box tests. Two cohesive soil batch samples with varying activity were tested using two different interface plates (steel and silicon carbide sandpaper) of comparable surface roughness. Each soil batch-interface combination was tested under three different initial effective normal stresses and two different over consolidation ratios (OCRs). Undrained residual interface strength envelopes were developed for each soil batch-interface combination. The results from tests performed on steel interface showed an increase in residual undrained interface strength with plasticy and clay activity whereas a reverse trend was observed in the results of the tests performed using the sandpaper interface. This reinforces the importance of the choice of interface plate material (in addition to surface roughness) for PSI testing program to accurately capture the resistances offered by the seabed to pipe displacement.