JOURNALS

Documents published in Scipedia

• Análisis dinámico de presas

  J. Miquel, E. Oñate, J. Buil, E. Herrero

  Monograph CIMNE (1991). M5

  
  

  Abstract

  Se desarrolla en este trabajo un estudio numérico-experimental acerca del comportamiento dinámico de las presas bóvedas considerando su interacción con el agua del embalse. Para ello, se ha realizado un análisis de los factores que inciden más directamente en el comportamiento dinámico de tales tipos de estructuras. Dicho análisis se realiza mediante e lmétodo de los elementos finitos, estudiando distintas alternativas de formulación. Asimismo, se ha realizado un esayo a escala real de una presa bóveda existente, mediante una serie de explosiones y midiendo la respuesta obtenida.

  Abstract
  Se desarrolla en este trabajo un estudio numérico-experimental acerca del comportamiento dinámico de las presas bóvedas considerando su interacción [...]

  • 14
  •  read

• Stress, strain and energy splittings for anisotropic elastic solids under volumetric constraints

  C. Felippa, E. Oñate

  Computers and Structures (2003). Vol. 81 (13), pp. 1343-1357

  
  

  Abstract

  We define stress and strain splittings appropriate to linearly elastic anisotropic materials with volumetric constraints. The treatment includes rigidtropic materials, which develop no strains under a stress pattern that is a null eigenvector of the compliance matrix. This model includes as special case incompressible materials, for which the eigenvector is hydrostatic stress. The main finding is that pressure and volumetric strain must be redefined as effective quantities. Using this idea, an energy decomposition that exactly separates deviatoric and volumetric energy follows.

  Abstract
  We define stress and strain splittings appropriate to linearly elastic anisotropic materials with volumetric constraints. The treatment includes rigidtropic materials, [...]

  • 10
  •  read

• A finite element methodology for local/global damage evaluation in civil engineering structures

  A. Hanganu, E. Oñate, A. Barbat

  Computers and Structures (2002). Vol. 80 (20-21), pp. 1667-1687

  
  

  Abstract

  The paper introduces a new global damage evaluation method which leads to a meaningful global damage index. A numerical procedure for the prediction of local and global damage in civil engineering structures using the finite element method and a continuum damage model, is presented. The method is adequate for the computation of the limit load in reinforced concrete (RC) structures and for the prediction of the failure mechanisms. Details of the applied damage model are given together with a description of the finite element implementation and the procedure for computing the global damage parameters. Examples of applications of the methodology to the nonlinear analysis of a range of RC structures, are presented.

  Abstract
  The paper introduces a new global damage evaluation method which leads to a meaningful global damage index. A numerical procedure for the prediction of local and [...]

  • 8
  •  read

• Some algorithms to correct a geometry in order to create a finite element mesh

  R. Ribó, G. Bugeda, E. Oñate

  Computers and Structures (2002). Vol. 80 (16-17), pp. 1399-1408

  
  

  Abstract

  One of the major difficulties in meshing 3D complex geometries is to deal with non-proper geometrical definitions coming from CAD systems. Typically, CAD systems do not take care of the proper definition of the geometries for the analysis purposes. In addition, the use of standard CAD files (IGES, VDA, …) for the transfer of geometries between different systems introduce some additional difficulties. In this work, a collection of algorithms to repair and/or to improve the geometry definitions are provided. The aim of these algorithms is to make as easy as possible the generation of a mesh over complex geometries given some minimum requirements of quality and correctness. The geometrical model will be considered as composed of a set of NURBS lines and trimmed surfaces. Some examples of application of the algorithms and of the meshes generated from the corrected geometry are also presented in this work.

  Abstract
  One of the major difficulties in meshing 3D complex geometries is to deal with non-proper geometrical definitions coming from CAD systems. Typically, [...]

  • 12
  •  read

• A scalar damage model with a shear retention factor for the analysis of reinforced concrete structures: theory and validation

  R. Scotta, R. Vitaliani, A. Saetta, E. Oñate, A. Hanganu

  Computers and Structures (2001). Vol. 79 (7), pp. 737-755

  
  

  Abstract

  A local isotropic single parameter scalar model that can simulate the mechanical behaviour of quasi-brittle materials, such as concrete, is described. The constitutive law needs the mechanical characteristics and the fracture energy of concrete to be completely defined. The damage parameter is obtained directly from the value of an equivalent effective stress in order to reduce the computing effort. Due to the unique damage parameter, this model is suitable for the study of quasi-static problems involving monotonically increasing loads. The problem of localisation and mesh dependency have been partially overcome by using an enhanced local method in which a characteristic internal length related to the mesh dimension is employed instead of the characteristic fracture length. In this work, the model was enriched further with the introduction of a shear retention factor that accounts for the friction between the two surfaces of a crack. These new features assure a real improvement of the damage model, maintaining nevertheless its simplicity and low computing cost and making it suitable for the practical solution of large scale problems. Several numerical simulations of experimental tests, concerning fracture tests on concrete specimens and beams failing in shear, have been performed for the validation of the model. The main results from the numerical analyses are described and compared with the experimental ones.

  Abstract
  A local isotropic single parameter scalar model that can simulate the mechanical behaviour of quasi-brittle materials, such as concrete, is described. [...]

  • 19
  •  read

• A finite point method for elasticity problems

  E. Oñate, F. Perazzo, J. Canet

  Computers and Structures (2001). Vol. 79 (22-25), pp. 2151-2163

  
  

  Abstract

  The basis of the finite point method (FPM) for the fully meshless solution of elasticity problems in structural mechanics is described. A stabilization technique based on a finite calculus procedure is used to improve the quality of the numerical solution. The efficiency and accuracy of the stabilized FPM in the meshless analysis of simple linear elastic structural problems is shown in some examples of applications.

  Abstract
  The basis of the finite point method (FPM) for the fully meshless solution of elasticity problems in structural mechanics is described. A stabilization [...]

  • 27
  •  read

• A layer-wise triangle for analysis of laminated composite plates and shells

  S. Botello, E. Oñate, J. Miquel

  Computers and Structures (1999). Vol. 70 (6), pp. 635-646

  
  

  Abstract

  The paper presents a new triangle for analysis of laminate plates and shells. The in-plane degrees of freedom are interpolated quadratically whereas a linear layer-wise approximation is chosen for the normal displacement. A substructuring technique is used to eliminate the in-plane degrees of freedom during the assembly process thus reducing substantially the computationed costs. The element performance is evaluated in the static and dynamic analysis of di€erent laminate plate and shell structures

  Abstract
  The paper presents a new triangle for analysis of laminate plates and shells. The in-plane degrees of freedom are interpolated quadratically whereas a linear layer-wise approximation [...]

  • 13
  •  read

• Plate bending elements with discrete constraints: New triangular elements

  O. Zienkiewicz, R. Taylor, P. Papadopoulos, E. Oñate

  Computers and Structures (1990). Vol. 35 (4), pp. 505-522

  
  

  Abstract

  In recent years a series of elements based on Reissner-Mindlin assumptions and using discrete (collocation type) constraints has been introduced. These elements have proved to be very effective, however their relation to straightforward mixed approximations has not been clear. In this paper this relationship is discussed and the reasons for their success explained. This allows new and effective triangular elements to be developed. The presentation shows the close relationships with the DKT (Discrete Kirchhoff Theory) element previously available only for thin plates and allows extension of their applications.

  Abstract
  In recent years a series of elements based on Reissner-Mindlin assumptions and using discrete (collocation type) constraints has been introduced. These elements have [...]

  • 23
  •  read

• Dynamic analysis of structures using a Reissner-Mindlin finite strip formulation

  J. Canet, B. Suarez, E. Oñate

  Computers and Structures (1989). Vol. 31 (6), pp. 967-975

  
  

  Abstract

  In this paper a finite strip formulation based on Reissner-Mindlin plate theory for dynamic analysis of prismatic shell type structure is presented. Detailed expressions of the relevant strip matrices for a variety of structures using the simple two node linear strip element are given. Examples of the good performance of the linear strip element for free and forced vibration analysis of plates, bridges and axisymmetric shells are presented.

  Abstract
  In this paper a finite strip formulation based on Reissner-Mindlin plate theory for dynamic analysis of prismatic shell type structure is presented. Detailed expressions of [...]

  • 13
  •  read

• A comparison of the linear, quadratic and cubic mindlin strip elements for the analysis of thick and thin plates

  E. Oñate, B. Suarez

  Computers and Structures (1983). Vol. 17 (3), pp. 427-439

  
  

  Abstract

  The behaviour of the linear, quadratic and cubic elements of the Mindlin plate strip family for thick and very thin plate analysis is investigated in this paper. Selective integration techniques are used to ensure the good behaviour of the elements when dealing with thin plates. Numerical results showing the convergence and accuracy of the elements for the analysis of plates of a wide range of thicknesses are given. The general performance of the three elements is discussed in detail. In particular, the linear element with a single integration point seems to be the best value strip element for practical purposes.

  Abstract
  The behaviour of the linear, quadratic and cubic elements of the Mindlin plate strip family for thick and very thin plate analysis is investigated in this paper. Selective [...]

  • 14
  •  read