Analysis of the manufacturing process of a car bonnet using Compression Resin Transfer Moulding (CRTM)

<span id="_GoBack"></span>

==1 Introduction==

Using Carbon fibre reinforced polymers (CFRP) in the automotive industry can reduce up to 70% of a cars weight and dissipate up to five times higher impact energies than metals [1]. However, the high manufacturing cost and cycle times associated to techniques such as prepreg + autoclave or Resin Transfer Moulding (RTM) have limited a wider use of CFRP [2]. RTM is a manufacturing process that has been applied for many years and is therefore well established [3], especially in aeronautic industry. However, in structural applications where higher fibre volume fractions (>50 %) are needed, the impregnation of the preform is more difficult because the permeability decreases; this results in longer mould filling times, and a higher probability of producing defects such as incomplete impregnation of the preform, poorly impregnated areas, misalignment of fibres or the generation of high porosity and voids.

CRTM is a variation of RTM, which can help to overcome some of this difficulties [3, 4]. The process is very similar to RTM, but in the injection stage, the mould is kept a bit open, so the permeability of the preform increases, and sometimes even a gap is produced between the preform and the upper mould. This way, the resin can be injected very fast. After injecting all the needed resin, the mould is closed to the final thickness of the part, forcing the resin to flow transversally (through the thickness) instead of flowing in-plane of the component (like in RTM). The resin flow pattern in CRTM is complex, because during the injection stage the resin flows through the gap, but part of it also goes into the preform [5], and the final impregnation pattern will affect the resin flow during the compression stage, the force needed and the quality of the final component. Therefore, it is important to understand all the phenomena that take place and adequately characterize all the parameters that influence the process in order to optimize it in order to reduce cycle times without affecting the quality of the final component.

The main objective of this work is to manufacture a CFRP sports car bonnet using CRTM in a very short time, analysing and optimising the different phases that take place during the process. This work has been performed in the frame of ADVANCRTM European project (Eurostars). The partners of the project are Alpex (Austria), Fagor Arrasate – Mondragon Unibertsitatea (Spain), FHNW (Switzerland), Roctool (France) and Riba (Italy).

==2 Car bonnet description==

The original car bonnet is shown in figure 1. The materials chosen for this study are a 0/90 non-crimp fabric of HR 50k Carbon fibre of 300 g/m<sup>2</sup> (HPT300 C090) and a fast curing epoxy from Huntsman (XB 3538 /Aradur® 3475). An aesthetic external woven carbon fibre layer was also included. The configuration of the layup has been defined for having equivalent mechanical properties as the original bonnet (manufactured by prepreg + autoclave). The thickness of the bonnet is not constant, varying in different zones from 1 to 1,6 mm.

[[Image:Draft_Porcar_403745435-image5-c.png|600px]]

<div class="center" style="width: auto; margin-left: auto; margin-right: auto;">
<span style="text-align: center; font-size: 75%;">'''Figure 1.''' CFRP Maserati car bonnet.</span></div>

==3 Analysis of the CRTM process of the car bonnet==

The goal is to analyse the possibility of manufacturing the part with a CRTM cycle time of less than 4 min. In order to optimise the CRTM process, the resin injection stage has been simulated. For that, both the reinforcement and the matrix must be characterised.

==='''3.1''' Characterization of the reinforcement permeability===

The permeabilities of the carbon non-crimp fabric have been determined experimentally in both directions, in-plane and through the thickness (figures 2 and 3).

[[Image:Draft_Porcar_403745435-image6-c.png|600px]]

<div class="center" style="width: auto; margin-left: auto; margin-right: auto;">
<span style="text-align: center; font-size: 75%;">'''Figure 2: '''Experimental setup for in-plane permeability characterisation.</span></div>

<div class="center" style="width: auto; margin-left: auto; margin-right: auto;">
 [[Image:Draft_Porcar_403745435-image7-c.png|318px]] </div>

<div class="center" style="width: auto; margin-left: auto; margin-right: auto;">
<span style="text-align: center; font-size: 75%;">'''Figure 3: '''Experimental setup for through the thickness permeability characterisation.</span></div>

The results for in-plane permeability for 0º, 90º and ±45º and for different fibre volume fractions are shown in figures 4, 5 and 6 respectively. Through the thickness permeability is shown in figure 7.

[[Image:Draft_Porcar_403745435-image8.png|600px]]

<div class="center" style="width: auto; margin-left: auto; margin-right: auto;">
<span style="text-align: center; font-size: 75%;">'''Figure 4: '''In-plane permeability for 0º.</span></div>

<div class="center" style="width: auto; margin-left: auto; margin-right: auto;">
 [[Image:Draft_Porcar_403745435-image9.png|600px]] </div>

<div class="center" style="width: auto; margin-left: auto; margin-right: auto;">
<span style="text-align: center; font-size: 75%;">'''Figure 5: '''In-plane permeability for 90º.</span></div>

<div class="center" style="width: auto; margin-left: auto; margin-right: auto;">
 [[Image:Draft_Porcar_403745435-image10.png|600px]] </div>

<div class="center" style="width: auto; margin-left: auto; margin-right: auto;">
<span style="text-align: center; font-size: 75%;">'''Figure 6: '''In-plane permeability for ±45º.</span></div>

[[Image:Draft_Porcar_403745435-image11.png|600px]]

<div class="center" style="width: auto; margin-left: auto; margin-right: auto;">
<span style="text-align: center; font-size: 75%;">'''Figure 7: '''Through the thickness permeability.</span></div>

It can be seen that the permeability reduction as fibre volume fraction increases is almost linear in-plane, with significant differences for 0º, 90º and ±45º. On the other hand, the permeability in the transverse direction is three orders of magnitude lower (which implies that impregnation in that direction is more difficult), and it decays exponentially as fiber volume content increases.

For the cure kinetics, a modified Kamal-Sourour model has been used based on DSC analysis (Figure 8),

{| class="formulaSCP" style="width: 100%; text-align: center;" 
|-
| 
{| style="text-align: center; margin:auto;" 
|-
| <math display="inline">\frac{d\alpha }{dt}=\left( {k}_{1}+{k}_{2}{\alpha }^{m}\right) {\left( 1-\alpha \right) }^{n}</math>
|}
| style="width: 5px;text-align: right;white-space: nowrap;" | (1)
|}

{| class="formulaSCP" style="width: 100%; text-align: center;" 
|-
| 
{| style="text-align: center; margin:auto;" 
|-
| <math display="inline">{k}_{1}={A}_{1}exp\left( -\frac{{E}_{1}}{T}\right)</math>
|}
| style="width: 5px;text-align: right;white-space: nowrap;" | (2)
|}

{| class="formulaSCP" style="width: 100%; text-align: center;" 
|-
| 
{| style="text-align: center; margin:auto;" 
|-
| <math display="inline">{k}_{2}={A}_{2}exp\left( -\frac{{E}_{2}}{T}\right)</math>
|}
| style="width: 5px;text-align: right;white-space: nowrap;" | (3)
|}


where <math display="inline">\alpha</math>  is the curing degree, and <math display="inline">n,\, m,\, {E}_{1}</math>and <math display="inline">{E}_{2}</math> are constants.

[[Image:Draft_Porcar_403745435-image12-c.png|600px]]

<div class="center" style="width: auto; margin-left: auto; margin-right: auto;">
<span style="text-align: center; font-size: 75%;">'''Figure 8: '''Degree of cure over time dependent on curing temperature.</span></div>

As rheology model, Castro Macosko model has been used,

{| class="formulaSCP" style="width: 100%; text-align: center;" 
|-
| 
{| style="text-align: center; margin:auto;" 
|-
| <math display="inline">\quad \quad \quad \quad \quad \quad \, \, \eta \left( \alpha ,T,\overset{\cdot}{\gamma }\right) =</math><math>\frac{{\eta }_{0}\left( T\right) }{1+{\left( \frac{{\eta }_{0}\left( T\right) \overset{\cdot}{\gamma }}{{\tau }^{\ast }}\right) }^{1-n}}{\left( \frac{{\alpha }_{g}}{{\alpha }_{g}-\alpha }\right) }^{{C}_{1}+{C}_{2}\alpha }</math>
|}
| style="width: 5px;text-align: right;white-space: nowrap;" | (4)
|}

{| class="formulaSCP" style="width: 100%; text-align: center;" 
|-
| 
{| style="text-align: center; margin:auto;" 
|-
| <math display="inline">{\quad \quad \quad \quad \quad \quad \, \, \eta }_{0}\left( T\right) =</math><math>Bexp\left( \frac{{T}_{b}}{T}\right)</math>
|}
| style="width: 5px;text-align: right;white-space: nowrap;" | (5)
|}


where <math display="inline">\eta</math>  is the viscosity, <math display="inline">\overset{\cdot}{\gamma }</math> is the shear rate, <math display="inline">{C}_{1},\, {C}_{2},\, B</math> are constants and <math display="inline">T</math> is temperature. Both cure kinetics and rheological measurements were performed with state-of-the-art laboratory equipment as described in a previous work [6].

[[Image:Draft_Porcar_403745435-image13-c.png|600px]]

<div class="center" style="width: auto; margin-left: auto; margin-right: auto;">
<span style="text-align: center; font-size: 75%;">'''Figure 9: '''Viscosity over time for different curing temperatures.</span></div>

==='''3.2''' Isothermal vs variothermal curing===

In this study both, isothermal and variothermal approaches have been studied theoretically. In the isothermal approach, the mould can be heated using traditional water or oil tempering systems; however, the thermal inertia of these kind of moulds is very high i.e. 5 hours for increasing mould temperature from 20 to 85 ºC.

As an alternative, induction-heating systems only heat a thin layer of the metallic surface of the mould, which is directly contacting the part. This way, the thermal inertia is reduced drastically.

In figure 10 the cure progression of the epoxy resin is shown for different cure cycles dependant on the temperature profile.

[[Image:Draft_Porcar_403745435-image14-c.png|600px]]

<div class="center" style="width: auto; margin-left: auto; margin-right: auto;">
<span style="text-align: center; font-size: 75%;">'''Figure 10: '''Degree of cure dependant on mould temperature and curing time.</span></div>

In table 1 isothermal processes are compared with variothermal ones in terms of degree of cure, leftover time in liquid state and power consumption.

<div class="center" style="width: auto; margin-left: auto; margin-right: auto;">
<span style="text-align: center; font-size: 75%;">'''Table 1:''' Comparison of an isothermal injection compression process at 100 °C (scenario 1), at 110 °C (scenario 2), at 120 °C (scenario 3) with a variothermal injection compression process at 115 °C / 125 °C (scenario 4) and at 100 °C / 140 °C (scenario 5).</span></div>

{| style="width: 100%;border-collapse: collapse;" 
|-
|  style="border-top: 1pt solid black;border-bottom: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">'''Scenarios'''</span>
|  style="border-top: 1pt solid black;border-bottom: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">'''1'''</span>
|  style="border-top: 1pt solid black;border-bottom: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">'''2'''</span>
|  style="border-top: 1pt solid black;border-bottom: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">'''3'''</span>
|  style="border-top: 1pt solid black;border-bottom: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">'''4'''</span>
|  style="border-top: 1pt solid black;border-bottom: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">'''5'''</span>
|-
|  style="border-top: 1pt solid black;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">Initial temp [ºC]</span>
|  style="border-top: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">100</span>
|  style="border-top: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">110</span>
|  style="border-top: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">120</span>
|  style="border-top: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">115</span>
|  style="border-top: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">100</span>
|-
|  style="vertical-align: top;"|<span style="text-align: center; font-size: 75%;">Final temp [ºC]</span>
|  style="text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">100</span>
|  style="text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">110</span>
|  style="text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">120</span>
|  style="text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">125</span>
|  style="text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">120</span>
|-
|  style="vertical-align: top;"|<span style="text-align: center; font-size: 75%;">Injection time budget [s]</span>
|  style="text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">27</span>
|  style="text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">27</span>
|  style="text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">27</span>
|  style="text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">27</span>
|  style="text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">27</span>
|-
|  style="vertical-align: top;"|<span style="text-align: center; font-size: 75%;">Mould closing time budget [s]</span>
|  style="text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">5</span>
|  style="text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">5</span>
|  style="text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">5</span>
|  style="text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">5</span>
|  style="text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">5</span>
|-
|  style="vertical-align: top;"|<span style="text-align: center; font-size: 75%;">Calculate for last resin injected?</span>

<span style="text-align: center; font-size: 75%;">Delay=injection time, at 23ºC</span>
|  style="text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">no</span>
|  style="text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">no</span>
|  style="text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">no</span>
|  style="text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">no</span>
|  style="text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">no</span>
|-
|  style="vertical-align: top;"|<span style="text-align: center; font-size: 75%;">Final time, required liquid state [s]</span>
|  style="text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">32</span>
|  style="text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">32</span>
|  style="text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">32</span>
|  style="text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">32</span>
|  style="text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">32</span>
|-
|  style="vertical-align: top;"|<span style="text-align: center; font-size: 75%;">Start time of heating [s]</span>
|  style="text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">0</span>
|  style="text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">0</span>
|  style="text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">0</span>
|  style="text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">0</span>
|  style="text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">0</span>
|-
|  style="vertical-align: top;"|<span style="text-align: center; font-size: 75%;">Final time of heating [s]</span>
|  style="text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">240</span>
|  style="text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">240</span>
|  style="text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">240</span>
|  style="text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">240</span>
|  style="text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">240</span>
|-
|  style="vertical-align: top;"|<span style="text-align: center; font-size: 75%;">Heat-up time window [s]</span>
|  style="text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">240</span>
|  style="text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">240</span>
|  style="text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">240</span>
|  style="text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">240</span>
|  style="text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">240</span>
|-
|  style="vertical-align: top;"|<span style="text-align: center; font-size: 75%;">Heating ramp [ºC/s]</span>
|  style="text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">0</span>
|  style="text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">0</span>
|  style="text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">0</span>
|  style="text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">0.042</span>
|  style="text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">0.083</span>
|-
|  style="vertical-align: top;"|<span style="text-align: center; font-size: 75%;">Cooling ramp [ºC/s]</span>
|  style="text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">1</span>
|  style="text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">1</span>
|  style="text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">1</span>
|  style="text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">1</span>
|  style="text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">1</span>
|-
|  style="vertical-align: top;"|<span style="text-align: center; font-size: 75%;">Rest temp [ºC] (lower than start)</span>
|  style="text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">95</span>
|  style="text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">95</span>
|  style="text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">95</span>
|  style="text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">95</span>
|  style="text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">95</span>
|-
|  style="vertical-align: top;"|<span style="text-align: center; font-size: 75%;">Hold time at max. temp [s]</span>
|  style="text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">0</span>
|  style="text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">0</span>
|  style="text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">0</span>
|  style="text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">0</span>
|  style="text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">0</span>
|-
|  style="vertical-align: top;"|<span style="text-align: center; font-size: 75%;">Cooling time [s]</span>
|  style="text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">5.2</span>
|  style="text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">15.2</span>
|  style="text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">25.2</span>
|  style="text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">30</span>
|  style="text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">25</span>
|-
|  style="vertical-align: top;"|<span style="text-align: center; font-size: 75%;">Total cycle time [s]</span>
|  style="text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">245.2</span>
|  style="text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">255.2</span>
|  style="text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">265.2</span>
|  style="text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">270</span>
|  style="text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">265</span>
|-
|  style="vertical-align: top;"|<span style="text-align: center; font-size: 75%;">Degree of cure [mailto:@ @] Total cycle time</span>
|  style="text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">0.85</span>
|  style="text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">0.92</span>
|  style="text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">0.96</span>
|  style="text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">0.96</span>
|  style="text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">0.93</span>
|-
|  style="vertical-align: top;"|<span style="text-align: center; font-size: 75%;">Degree of cure [mailto:@ @] Final liquid time</span>
|  style="text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">0.22</span>
|  style="text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">0.33</span>
|  style="text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">0.47</span>
|  style="text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">0.41</span>
|  style="text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">0.23</span>
|-
|  style="vertical-align: top;"|<span style="text-align: center; font-size: 75%;">Leftover time still in liquid state [s]</span>
|  style="text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">57.5</span>
|  style="text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">23.5</span>
|  style="text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">3.5</span>
|  style="text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">10.5</span>
|  style="text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">45.0</span>
|-
|  style="border-bottom: 1pt solid black;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">Power [kW]</span>
|  style="border-bottom: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">15</span>
|  style="border-bottom: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">15</span>
|  style="border-bottom: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">15</span>
|  style="border-bottom: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">292</span>
|  style="border-bottom: 1pt solid black;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">573</span>
|}


Based on the results shown in table 1 and figure 10, the following statements can be made:

The higher the final mould temperature, the higher is the degree of cure after the total process cycle time.

Taking into account a curing degree below 95 % would not lead to sufficient mechanical and thermal properties, a mould temperature below 120 °C should be avoided. Additionally, the left over time of the resin being in a liquid state should be high enough (e.g. < 10 s) for a good impregnation of the fabric.

Considering these two prerequisites (enough time for impregnation of the fabric with low viscous resin and high degree of cure at the end of the cycle) one can see the advantage of a variothermal cycle: In scenario 4 (table 1) the resulting degree of cure would be 96 % with a leftover time of 10.5 seconds.

In order to save energy and costs for the variothermal system, the temperature delta in the variothermal process should be as small as possible. In scenario 5 (table 1) one can see that the leftover time would be 45 s but the degree of cure would be only 93 %. Additionally, an energy source with 573 kW would be needed. For the calculation of the power the mould size (''l ''= 2.2 m, ''w ''= 2.1 m, ''d'' = 0.3 m), mould mass, heating and cooling cycle, ramp time, injection time, heat time and heat loss were taken into account.

==='''3.3''' Simulation of the injection stage ===

The through-plane impregnation has been simulated with Autodesk® Moldflow® using a geometrically simplified model, and the same models for the cure kinetics and rheology as described in equations (1)-(3) and (4)-(5). Only the impact of shear was neglected. The permeability for the preform was applied according to the measurements from figure 4 to 7. The permeability for the gap <math display="inline">{K}_{gap}</math> depends on the thickness <math display="inline">{h}_{gap}</math> of the gap:

{| class="formulaSCP" style="width: 100%; text-align: center;" 
|-
| 
{| style="text-align: center; margin:auto;" 
|-
| <math display="inline">{K}_{gap}=\frac{{h}_{gap}^{2}}{12}</math>
|}
| style="width: 5px;text-align: right;white-space: nowrap;" | (6)
|}


Preliminary simulations were carried out to check the suitability of Moldflow® for this process. Especially the meshing was demanding and lead to high aspect ratios of the elements because a good resolution was needed over the thickness for the large-area but thin bonnet. The detailed parameters of the simulation can be found in table 2:

<div class="center" style="width: auto; margin-left: auto; margin-right: auto;">
<span style="text-align: center; font-size: 75%;">'''Table 2:  '''Moldflow® parameters used for cure kinetics and rheology of the resin impregnating the fabric</span></div>

{| style="width: 81%;margin: 1em auto 0.1em auto;border-collapse: collapse;" 
|-
|  colspan='2'  style="border-top: 1pt solid black;border-bottom: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">'''Reactive viscosity model'''</span>
|  colspan='2'  style="border-top: 1pt solid black;border-bottom: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">'''Kinetic of n-th order'''</span>
|-
|  style="border-top: 1pt solid black;text-align: center;"|<math>n</math>
|  style="border-top: 1pt solid black;border-right: 1pt solid black;text-align: center;"|<math>1\times {10}^{-15}</math>
|  style="border-top: 1pt solid black;border-left: 1pt solid black;text-align: center;"|<math>H</math>
|  style="border-top: 1pt solid black;text-align: center;vertical-align: top;"|<math>475000\frac{J}{kg}</math>
|-
|  style="text-align: center;vertical-align: top;"|<math>{\tau }^{\ast }</math>
|  style="border-right: 1pt solid black;text-align: center;vertical-align: top;"|<math display="inline">1\times {10}^{-15}\, Pa</math>
|  style="border-left: 1pt solid black;text-align: center;vertical-align: top;"|<math>m</math>
|  style="text-align: center;vertical-align: top;"|<math>1.911</math>
|-
|  style="text-align: center;vertical-align: top;"|<math>B</math>
|  style="border-right: 1pt solid black;text-align: center;vertical-align: top;"|<math>1\times {10}^{-15}Pa\cdot s</math>
|  style="border-left: 1pt solid black;text-align: center;vertical-align: top;"|<math>n</math>
|  style="text-align: center;vertical-align: top;"|<math>1.732</math>
|-
|  style="text-align: center;vertical-align: top;"|<math>{T}_{b}</math>
|  style="border-right: 1pt solid black;text-align: center;vertical-align: top;"|<math>5772.7\, K</math>
|  style="border-left: 1pt solid black;text-align: center;vertical-align: top;"|<math>{A}_{1}</math>
|  style="text-align: center;vertical-align: top;"|<math>1.336\, {s}^{-1}</math>
|-
|  style="text-align: center;vertical-align: top;"|<math>{c}_{1}</math>
|  style="border-right: 1pt solid black;text-align: center;vertical-align: top;"|<math>7.528</math>
|  style="border-left: 1pt solid black;text-align: center;vertical-align: top;"|<math>{A}_{2}</math>
|  style="text-align: center;vertical-align: top;"|<math>35645\, {s}^{-1}</math>
|-
|  style="text-align: center;vertical-align: top;"|<math>{c}_{2}</math>
|  style="border-right: 1pt solid black;text-align: center;vertical-align: top;"|<math>-9,693</math>
|  style="border-left: 1pt solid black;text-align: center;vertical-align: top;"|<math>{E}_{1}</math>
|  style="text-align: center;vertical-align: top;"|<math>7068.31\, K</math>
|-
|  style="border-bottom: 1pt solid black;text-align: center;vertical-align: top;"|<math>{\alpha }_{g}</math>
|  style="border-bottom: 1pt solid black;border-right: 1pt solid black;text-align: center;vertical-align: top;"|<math>0.6317</math>
|  style="border-left: 1pt solid black;border-bottom: 1pt solid black;text-align: center;vertical-align: top;"|<math>{E}_{2}</math>
|  style="border-bottom: 1pt solid black;text-align: center;vertical-align: top;"|<math>5306.6\, K</math>
|}


Significant differences are observed between flow front advancement in the gap and in the preform (figures 11, figure 12 and table 3. This advancement depends mostly on gap thickness, when considering the same preform.

[[Image:Draft_Porcar_403745435-image15.png|600px]]  [[Image:Draft_Porcar_403745435-image16.png|600px]]

<div class="center" style="width: auto; margin-left: auto; margin-right: auto;">
<span style="text-align: center; font-size: 75%;">'''Figure 11: '''Schematic view and simulation results of difference in flow front advancement because of much higher permeability of the resin trough the gap compared to the preform or fabric.</span></div>

<div class="center" style="width: auto; margin-left: auto; margin-right: auto;">
<span style="text-align: center; font-size: 75%;">'''Table 3:''' Difference in flow front advancement dependent on gap thickness in the compression mould</span></div>

{| style="width: 100%;border-collapse: collapse;" 
|-
|  style="border-top: 1pt solid black;border-bottom: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">'''Gap thickness [mm]'''</span>
|  style="border-top: 1pt solid black;border-bottom: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">'''Difference in flow front advancement [mm]'''</span>
|-
|  style="border-top: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">0.5</span>
|  style="border-top: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">200</span>
|-
|  style="border-bottom: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">1</span>
|  style="border-bottom: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">342</span>
|}


A smaller gap (and hence higher flow resistance) decreases the difference in the flow front advancement when filling large flat cavities such as a bonnet by injection compression moulding.

[[Image:Draft_Porcar_403745435-image17.png|600px]]

<div class="center" style="width: auto; margin-left: auto; margin-right: auto;">
<span style="text-align: center; font-size: 75%;">'''Figure 12: '''Bottom view of the flow front in the gap and preform of the bonnet mould with one central injection gate. The different layers can be seen clearly.</span></div>

==4 Manufacturing of the car bonnet==

==='''4.1''' Description of the mould===

The mould has been built in aluminium, as it is not intended for an intensive industrial use. The overall size of the mould is 2140mm × 2140mm × 700 mm and has a total mass of around 6000 kg. An exploded view of the mould is shown in figure 13. In figure 14 the mould is shown closed, all together with the injection head and the component. The mould has four vacuum points in the four corners, and the possibility of injecting the resin through a centred injection point, through an injection point located at the front of the bonnet. This way, two different injection strategies can be tested: radial (centred) and linear (front to rear), as shown in Figure 15 (a) and (b), respectively.

<div class="center" style="width: auto; margin-left: auto; margin-right: auto;">
 [[Image:Draft_Porcar_403745435-image18.png|396px]] </div>

<div class="center" style="width: auto; margin-left: auto; margin-right: auto;">
<span style="text-align: center; font-size: 75%;">'''Figure 13: '''Exploded view of the mould.</span></div>

<div class="center" style="width: auto; margin-left: auto; margin-right: auto;">
 [[Image:Draft_Porcar_403745435-image19.png|600px]] </div>

<div class="center" style="width: auto; margin-left: auto; margin-right: auto;">
<span style="text-align: center; font-size: 75%;">'''Figure 14:''' Closed mould with the part inside and a centred injection point.</span></div>

{| style="width: 100%;border-collapse: collapse;" 
|-
|  style="text-align: center;vertical-align: top;width: 49%;"|[[Image:Draft_Porcar_403745435-image20.png|294px]] (a)
|  style="text-align: center;vertical-align: top;width: 50%;"|[[Image:Draft_Porcar_403745435-image21.png|300px]] (b)
|}


<div class="center" style="width: auto; margin-left: auto; margin-right: auto;">
<span style="text-align: center; font-size: 75%;">'''Figure 15: '''Two resin injection strategies: Radial and linear.</span></div>

The mould has been manufactured including a traditional water/oil heating circuit; taking into account the big size of the mould, the power needed by the induction system for the variothermal tests was too high.

==='''4.2''' Manufacturing parameters===

For the experimental manufacturing tests, it has not been possible to replicate the theoretically analysed cases. The thermal inertia of such a big mould together with the heating system available, allowed a maximum test temperature of only 100ºC (and most of the tests have been performed at around 80ºC). For this reason, the target cycle time has been increased to 30 min.

When manufacturing the bonnet, different parameters have been considered:

''Mould parameters:''

a) Gap size: depending on the gap size, the resin can be injected faster (bigger gap) or slower (smaller gap). However, a smaller gap means that the resin will be more dispersed on the preform, occupying a larger area, which in consequence would produce a better-impregnated preform once the mould is closed.

b) Temperature of the mould: The resin is a fast curing epoxy resin; the temperature of the mould will highly affect the time needed for the resin to cure. Higher mould temperatures will reduce the curing time, but can also affect the filling time since if the viscosity can increase while the mould is being filled, and this could make more difficult and even prevent the total filling of the mould.

c) Position of the injection and vacuum points: There are two injection points that can be used (one at a time). There are also four vacuum points that can be connected and disconnected during the injection and compression phases in order to try to direct the flow to specific directions.

''Injection machine parameters:''

d) Resin volume: The theoretical resin volume needed is determined, but more resin must be injected considering that some of the resin will fill the distribution channels, tubes, injection point or vacuum holes.

e) Flow-rate and injection pressure: These parameters will determine the injection time and must be carefully selected; if the viscosity of the resin is too high for the injection machine to inject the selected quantity, the system will not be able to function correctly.

f) Resin temperature. If the resin is kept warmer in the deposit of the injection machine (before it is mixed with the catalyst) the resin will be injected more easily than if it is kept cooler. In this case the influence of the resin temperature has not been analysed, but previous tests have demonstrated that a set point temperature of the resin deposit of 60º C was needed in order to assure a correct function of the injection machine.

Considering all these parameters, and taking into account the time limitation for this phase, the influence of only some of them has been analysed (Table 4).

<div class="center" style="width: auto; margin-left: auto; margin-right: auto;">
<span style="text-align: center; font-size: 75%;">'''Table 4:''' Car bonnet manufacturing parameters.</span></div>

{| style="width: 100%;border-collapse: collapse;" 
|-
|  rowspan='2' style="border: 1pt solid black;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">Test number</span>
|  rowspan='2' style="border: 1pt solid black;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">Gap (mm)</span>
|  rowspan='2' style="border: 1pt solid black;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">Mould temperature [ºC]</span>
|  rowspan='2' style="border: 1pt solid black;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">Resin temperature [ºC]</span>
|  rowspan='2' style="border: 1pt solid black;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">Injection strategy</span>
|  rowspan='2' style="border: 1pt solid black;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">Resin volume [l]</span>
|  rowspan='2' style="border: 1pt solid black;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">Injection pressure [bar]</span>
|  rowspan='2' style="border: 1pt solid black;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">Closing velocity [mm/s]</span>
|  rowspan='2' style="border: 1pt solid black;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">Vacuum [yes/no]</span>
|  colspan='3'  style="border: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">time</span>
|-
|  style="border: 1pt solid black;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">Injection (s)</span>
|  style="border: 1pt solid black;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">Compression [s]</span>
|  style="border: 1pt solid black;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">Curing [min]</span>
|-
|  style="border: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">1</span>
|  style="border: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">3.3</span>
|  style="border: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">82</span>
|  style="border: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">60</span>
|  style="border: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">Centre</span>
|  style="border: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">1.8/1.8</span>
|  style="border: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">5</span>
|  style="border: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">1</span>
|  style="border: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">-</span>
|  style="border: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">30</span>
|  style="border: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">5</span>
|  style="border: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">30</span>
|-
|  style="border: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">2</span>
|  style="border: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">1.3</span>
|  style="border: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">86</span>
|  style="border: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">60</span>
|  style="border: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">Centre</span>
|  style="border: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">0.6/1.8</span>
|  style="border: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">5</span>
|  style="border: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">1</span>
|  style="border: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">Yes</span>
|  style="border: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">180</span>
|  style="border: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">5</span>
|  style="border: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">30</span>
|-
|  style="border: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">3</span>
|  style="border: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">3.3</span>
|  style="border: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">82</span>
|  style="border: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">60</span>
|  style="border: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">Centre</span>
|  style="border: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">0.5/2.2</span>
|  style="border: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">5</span>
|  style="border: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">1</span>
|  style="border: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">-</span>
|  style="border: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">180</span>
|  style="border: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">5</span>
|  style="border: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">30</span>
|-
|  style="border: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">4</span>
|  style="border: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">3.3</span>
|  style="border: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">83</span>
|  style="border: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">60</span>
|  style="border: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">Centre</span>
|  style="border: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">2.2/2.2</span>
|  style="border: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">5</span>
|  style="border: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">1</span>
|  style="border: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">Yes</span>
|  style="border: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">30</span>
|  style="border: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">5</span>
|  style="border: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">30</span>
|-
|  style="border: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">5</span>
|  style="border: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">3.3</span>
|  style="border: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">80</span>
|  style="border: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">60</span>
|  style="border: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">Front</span>
|  style="border: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">2.2/2.2</span>
|  style="border: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">5</span>
|  style="border: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">1</span>
|  style="border: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">Yes</span>
|  style="border: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">108</span>
|  style="border: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">5</span>
|  style="border: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">30</span>
|-
|  style="border: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">6</span>
|  style="border: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">3.3</span>
|  style="border: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">75</span>
|  style="border: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">60</span>
|  style="border: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">Front</span>
|  style="border: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">2.2/2.2</span>
|  style="border: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">5</span>
|  style="border: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">1</span>
|  style="border: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">Yes</span>
|  style="border: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">28</span>
|  style="border: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">5</span>
|  style="border: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">20</span>
|-
|  style="border: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">7</span>
|  style="border: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">3.3</span>
|  style="border: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">99</span>
|  style="border: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">60</span>
|  style="border: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">Centre</span>
|  style="border: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">2.2/2.2</span>
|  style="border: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">5</span>
|  style="border: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">1</span>
|  style="border: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">Yes</span>
|  style="border: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">60</span>
|  style="border: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">5</span>
|  style="border: 1pt solid black;text-align: center;vertical-align: top;"|<span style="text-align: center; font-size: 75%;">30</span>
|}


==='''4.3''' Results===

After having carried out the bonnet manufacturing tests, some of the observations concerning the results are set out below.

In test nº1 the process has been ok, but not enough resin was injected, resulting in a non-fully impregnated part (figure 16).

In test nº2 the gap size has been too small, the injection machine has not been able to inject all the resin into the mould (figure 17).

In test nº 3 the preform has not been previously compacted, and the injection machine has not been able to inject the resin into the mould. The result (figure 18) is similar to test number 2.

The test nº 4 has given the best result (figure 19), even if the presence of race-tracking has left some dry spots in the part.

In test number 5 there was a problem with the valve of the injection machine, and almost no resin was injected to the preform.

In test number 6 resin was injected from the front part of the bonnet, but race tracking occurred in the perimeter of the preform. The resin did not impregnate a big central part of the preform (figure 20).

In test number 7 the mould has been at a higher temperature (99ºC), which has increased the viscosity of the resin very fast; in consequence, the injection machine has not been able to inject all the resin, so the injection phase had to be stopped in order to preserve the injection machine itself from being blocked with cured resin.

[[Image:Draft_Porcar_403745435-image22-c.jpeg|600px]]

<div class="center" style="width: auto; margin-left: auto; margin-right: auto;">
<span style="text-align: center; font-size: 75%;">'''Figure 16: '''Resulting bonnet for test nº 1: Partially impregnated.</span></div>

[[Image:Draft_Porcar_403745435-image23-c.jpeg|600px]]

<div class="center" style="width: auto; margin-left: auto; margin-right: auto;">
<span style="text-align: center; font-size: 75%;">'''Figure 17: '''Resulting bonnet for test nº 2: Partially impregnated due to a too small gap.</span></div>

<div class="center" style="width: auto; margin-left: auto; margin-right: auto;">
 [[Image:Draft_Porcar_403745435-image24-c.jpeg|600px]] </div>

<div class="center" style="width: auto; margin-left: auto; margin-right: auto;">
<span style="text-align: center; font-size: 75%;">'''Figure 18: '''Resulting bonnet for test nº 3: Partially impregnated due to a non-compacted preform.</span></div>

<div class="center" style="width: auto; margin-left: auto; margin-right: auto;">
 [[Image:Draft_Porcar_403745435-image25-c.jpeg|600px]] </div>

<div class="center" style="width: auto; margin-left: auto; margin-right: auto;">
<span style="text-align: center; font-size: 75%;">'''Figure 19: '''Resulting bonnet for test nº 4: Almost fully impregnated with some dry spots due to race-tracking.</span></div>

<div class="center" style="width: auto; margin-left: auto; margin-right: auto;">
 [[Image:Draft_Porcar_403745435-image26-c.jpeg|600px]] </div>

<div class="center" style="width: auto; margin-left: auto; margin-right: auto;">
<span style="text-align: center; font-size: 75%;">'''Figure 20: '''Resulting bonnet for test nº 6: Injection point in the front of the bonnet. Partially impregnated due to race-tracking through the perimeter of the preform</span></div>

==5 Conclusions==

In this work, the CRTM manufacturing process of a sports car has been studied. The in-plane and through-the-thickness permeabilities of the reinforcement have been measured for different fibre content values. An almost linear decay of permeability has been observed as fibre content increases in-plane from 40% to 60%, with significant differences depending on the fibre direction, being ±45º the one that showed the least permeability.

Through-the-thickness permeability has been three orders of magnitude lower than in-plane, and it decays exponentially as fiber volume content increases for the same fibre content range.

The curing kinetics of the resin has been modelled using a modified Kamal-Sourour model, and a Castro Macosko model has been used as rheology model. The cure progression of the resin has been defined for different cure cycles dependant on the temperature profile. Some of these scenarios include isothermal profiles, while others include variothermal approaches. There are two scenarios in which a 95% of curing degree is reached in 240 s: One isothermal (with a mould temperature of 120ºC), and the other variothermal (from 115ºC to 125ºC). The advantage of using a variothermal approach has been demonstrated because the resin leftover time still in liquid state is three times bigger; however, the amount of energy needed for the variothermal scenario also increases drastically.

It has not been possible to replicate the theoretical analysis experimentally, mainly due to the high thermal inertia of the mould. In consequence, a lower mould temperature has been chosen and a new target cycle time of 30 min has been established. Only one of the tests performed resulted in an almost total impregnated component.

==Acknowledgements==

The authors gratefully acknowledge the support of the European Union via project ADVANCRTM (10032/14/22619/Ae), the Basque Government (Programa Predoctoral de Formación de Personal Investigador No Doctor, PRE_2014_1_402) and Diputación Foral de  Guipuzkoa (OF 144/2014).

==References==

[1] A. Esnaola, I. Tena, J. Aurrekoetxea, I. Gallego and I Ulacia, Composites Part B: Engineering'' '' '''85''', 1 (2016).

[https://doi.org/10.1016/j.compositesb.2015.09.007 https://doi.org/10.1016/j.compositesb.2015.09.007]

[2] M.G. Bader, Composites Part A: Applied Science and Manufacturing'' '' '''33''', 913 (2002).

[https://doi.org/10.1016/S1359-835X(02)00044-1 https://doi.org/10.1016/S1359-835X(02)00044-1]

[3] C.D. Rudd, A.C. Long, K.N. Kendall, C.Mangin. Liquid Moulding Rechnologies, '''1''' (1997)

[https://doi.org/10.1533/9781845695446.1 https://doi.org/10.1533/9781845695446.1]

[4] M. Baskaran, I. Ortiz de Mendibil, M. Sarrionandia, J. Aurrekoetxea, J. Acosta, U. Argarate and D. Chico. 16th European Conference in Composite Materials, Seville, Spain, n.d.: 22-622-26 June (2014)

[https://doi.org/10.1002/admt.201800271 https://doi.org/10.1002/admt.201800271]

[5] P. Simaneck and S.G. Advani, Revue européenne des elements finis, '''14''', 777 (2005)

[6] R. Geinsberger, J. Maldonado, N. Bahamonde, A. Keller, C. Dransfeld, K. Masania. Composites Part B: Engineering'' '' '''124''', 182 (2017).

[https://doi.org/10.1016/j.compositesb.2017.05.040 https://doi.org/10.1016/j.compositesb.2017.05.040]